3D printing spray adhesive: why the first layer determines the success of your print

If you’ve been 3D printing for a while, you know it well: the first layer is the moment of truth. That’s where it’s decided whether your print will become a perfect part or a pile of crooked filament to toss in the bin.

Warping, sudden detachments, lifted corners, parts that shift mid-print: in the vast majority of cases, all of this depends on insufficient adhesion between the filament and the build plate. And the solution isn’t having more luck, but having the right tool.

That tool is called 3Dbooster Lock, and in this article I’ll explain why more and more hobbyists, professionals, and companies in Italy are choosing it for their prints.

---

The problem that keeps you up at night: warping and bed detachment

Let’s start with the real pain, the one every maker knows:

• you open the printer in the morning and find a “spaghetti monster” instead of your part;
• the corner of your ABS has lifted by 3 millimeters halfway through the print;
• you spent 12 hours printing and 200 grams of PETG for an unusable prototype;
• you try again, change the parameters, and fail again.

All of this comes with a cost that isn’t just the filament: it’s time, electricity, and frustration.

A stable first layer is the foundation for everything else. If it gives way, the print is compromised. Period.

---

What 3Dbooster Lock is and why it’s different from DIY solutions

You may have already tried the classic alternatives: hairspray, glue stick, Kapton tape, adhesive sheets. They work… halfway. The problem is that they need to be applied every time, they get messy, leave annoying residue, and often aren’t enough with engineering materials.

3Dbooster Lock is an aerosol spray adhesive specifically designed for 3D printing, made in Italy, that works intelligently with temperature:

• Above 45°C → acts as a tackifier, keeping the part firmly attached to the bed throughout the print;
• Below 45°C → promotes release, allowing you to remove the part without forcing or damaging the bed.

This is thermal behavior that generic solutions simply don’t have. And it has a very interesting side effect: for some TPU it’s used specifically to promote release from the build plate (TPU adhesion is already more than enough on its own—the risk is the opposite, the part that won’t come off!).

Discover all the details and buy 3Dbooster Lock on the official shop: 👉 https://www.3dbooster.com/it/shop/3dbooster-lock-lacca-colla-stampa3d/

---

The feature that really makes the difference: it lasts for a huge number of prints

Let’s get to the economic point, the one that’s often overlooked.

Most 3D printing adhesives need to be applied for every print. Every time. Spray, wait, repeat. Over time, that 10-euro can is gone in a month.

3Dbooster Lock works the opposite way: a single application lasts for multiple consecutive prints. You don’t need to spray it every time, only when adhesion starts to drop. Result:

• 🧴 one can lasts much longer → cost per individual print drastically reduced;
• ⏱️ zero prep before every print → power on and print;
• 🧼 less bed maintenance → less residue, less cleaning, less stress.

In the long run, it’s the most cost-effective choice in its category. It’s not the cheapest can to buy: it’s the least expensive to use.

---

Universal compatibility: from PLA to Polycarbonate

One of the reasons makers love it is its versatility. You don’t need one adhesive for PLA, one for ABS, one for PC. Just one, for (almost) everything:

✅ PLA — perfect adhesion eliminates detachments even on long prints; ✅ PETG — a material famous for “biting” the bed too much or too little: with Lock it stays stable and releases without drama; ✅ ABS and ASA — the warping champions finally kept under control, even on large parts; ✅ PC, PC-PBT, PC-ABS — high-temperature engineering materials, where weak adhesives give up; ✅ TPU — used to promote post-print release; ✅ other filaments — the formula covers practically the entire FDM range.

The product is ideal for PEI, glass, and steel surfaces, the most common materials in modern build plates.

---

How to use 3Dbooster Lock: the 6-step guide

Using it is very simple, but follow the order to get the best results:

1. Thoroughly clean the build plate of dust and residue;
2. Make sure the bed temperature is below 50°C;
3. Spray evenly over the entire surface;
4. Heat the bed to the printing temperature and start the job;
5. After printing, wait for the bed to drop below 45°C and remove the part easily;
6. Clean with a sponge and lukewarm water to remove any residue.

💡 Practical tip: as with any aerosol product, always test on a small area of the bed the first time.

---

Who it’s designed for (spoiler: you)

• 🏠 Hobbyists and makers: no more overnight failures—print with confidence even long parts;
• 💼 Professionals and prototypers: stable prints = less scrap = higher margins;
• 🏭 Manufacturing companies: reduce errors and material waste on repeated production runs;
• 🎓 Schools, fablabs and makerspaces: its ease of use makes it perfect even for beginners.